We compare ways of draining a patio, not manufacturers or product lines. The load classes mentioned come from the published European standard for drainage channels. We haven't tested any product, and the right answer for your patio depends on ground conditions that only a site visit can establish.
Every patio drainage job comes down to two questions. How does the water get off the paving, and where does it go next? The first is about falls, channels and joints. The second is about soakaways, existing drains and what your soil will accept. Most failures happen because someone answered the first question and forgot the second.
Our patio drainage installation page names the main methods. Here they are compared, plus two that often get forgotten.
The options at a glance
Typical price bands are from our patio drainage cost guide and depend on length, access, ground and whether paving has to be lifted.
| Method | What it does | Works well for | Not the answer when | Typical cost band |
|---|---|---|---|---|
| Correcting the falls | Re-lays paving with a slope so water runs off | Patios laid flat or falling towards the house | Water already runs off but has nowhere to go | £700 – £1,100 for a section |
| Channel or linear drain | Collects water along a line and pipes it away | Along a house wall, at door thresholds, at the bottom of a fall | There's no suitable discharge point within reach | £400 – £700 short run |
| Point drain or gully | Collects water at one low spot | A single low corner | Water is spread along an edge | Usually at the lower end |
| Gravel edge drain | A gravel-filled trench along an open edge, often with a perforated pipe | Patios ending at a lawn or border | Clay soils, unless piped onwards | Varies with length |
| Soakaway | Lets collected water disperse into the ground | Free-draining soils with no drain nearby | Heavy clay, high water tables, too close to the house | Part of £1,100 – £1,500+ full systems |
| Permeable jointing | Lets rain drain down through open joints | New patios on a free-draining base | An existing patio on a dense, sealed base | Built into a new install |
Correcting the falls
If a patio is flat or slopes towards the house, nothing else on this list will work well until that's fixed. The paving is lifted, the sub-base re-shaped with a proper fall away from the building and the slabs re-bedded. It's disruptive, and it's often combined with a channel at the bottom of the new fall. Our guide to how a patio is laid explains where the fall should be built in.
Channel and linear drains
A slotted or grated channel set into the paving, flush with the surface, that catches water running across it and carries it to a pipe. Along the house wall and in front of patio doors, this is the standard answer, because it intercepts the water before it reaches the brickwork or the threshold. Slim slot drains suit porcelain and modern designs; wider grated channels hold more water.
EN 1433, the European standard for drainage channels, sorts them into load classes. A15 is the lightest, meant for pedestrian areas such as a garden patio; heavier classes such as B125 are for driveways and car parks. A patio channel doesn't need to be over-specified, but if a car will ever drive across it, it needs the higher class.
The channel itself is rarely the expensive part. What it connects to is. The patio drainage cost guide explains why the discharge point decides the bill.
Point drains and gullies
A single drain at the lowest spot, with the paving falling towards it from more than one direction. It suits a patio that naturally sheds water to one corner, and it's less visible than a long channel. It needs more careful laying, because the slabs around it have to be cut and set to fall into it.
Gravel edge drains
Where a patio ends at a lawn or border, a narrow trench filled with clean gravel along the bottom edge can catch run-off and let it soak away gradually, sometimes with a perforated pipe in the base to carry water onwards. It's simple and cheap on free-draining ground. On clay, it fills up and stays full unless the pipe leads somewhere useful.
Soakaways
A soakaway is a pit, filled with rubble or, more often now, plastic crates wrapped in a membrane, where collected water is held and slowly soaks into the surrounding soil. It's the usual destination when there's no suitable surface water drain nearby.
Its weakness is the ground. On sandy or gravelly soil a soakaway works well. On heavy clay, water barely moves, and a soakaway can sit full for days. That's why a percolation test, digging a trial hole, filling it and timing how quickly it drains, is normally done before one is designed. Soakaways also need to be kept a sensible distance from buildings, so the water doesn't end up undermining the foundations it was meant to protect. On clay, connecting to an existing surface water drain, where that's allowed, is often the more reliable answer.
Permeable jointing
Instead of collecting water and taking it somewhere, permeable paving lets it drain straight through: slabs laid with open joints filled with a permeable grit or a permeable jointing compound, over a free-draining sub-base. Less water runs off the surface in the first place.
It's a design decision for a new patio rather than a fix for an old one, because the whole build-up has to be permeable. A conventional sub-base and mortar bed underneath will just hold the water. It's also the method most affected by soil: on clay, the water has to be taken away from the base of the sub-base by a pipe. For front gardens in England, permeable surfacing is one way to meet the planning rule on hard surfaces, covered in our planning permission guide. Interpave, the precast paving trade body, publishes guidance on permeable paving design.
Combining them
Most real jobs use two or three of these together. A typical retrofit on a patio that holds water against the house might be: re-lay the paving nearest the wall with a fall away from it, set a channel drain along the wall to catch anything that still arrives, and pipe it to an existing drain or a new soakaway. A typical new build on free-draining ground might simply use a good fall and a gravel edge drain.
However it's collected, surface water has to go somewhere legitimate: a soakaway, a surface water drain where connection is permitted, or a watercourse with any consent required. It shouldn't be sent onto a neighbour's land or the public highway. Where new drainage connects to existing drains or runs close to the building, Approved Document H can apply.
Not sure which you need? Our guide to water pooling on a patio helps match the symptom to the method.
Frequently asked questions
What is the best drainage for a patio?
There isn't one best method. A correct fall is the foundation of any patio drainage. A channel drain along the house wall is the standard way to keep water off the brickwork. Where the water goes next, a soakaway or an existing drain, depends on your soil and what's nearby.
Do I need a soakaway for patio drainage?
Only if there's nowhere else suitable for the water to go. Where a surface water drain is close by and connection is allowed, that's often simpler. Soakaways also work poorly on heavy clay, so a percolation test is normally done first.
What load class of channel drain does a patio need?
Under the EN 1433 standard, class A15 covers pedestrian areas such as garden patios. If vehicles will cross the drain, for example where a patio meets a driveway, a higher class such as B125 is needed.
Can permeable jointing be added to an existing patio?
Usually not effectively. Permeable paving relies on the whole build-up underneath being free-draining. On an existing patio with a conventional sub-base and mortar bed, opening the joints just lets water into a base that holds it.
Ready to talk to a patio installation specialist?
Get Free Quotes →
